Ford Fiesta Large Cup Holder Expander

Description

Conveniently hold your big water bottle in your Ford Fiesta with this adjustable, custom-fit, multi-piece cup holder expander set. The adapter is designed and 3d printed for the Fiesta and snaps tightly into the rear cup holder using its spring tabs for a flush and secure fit to hold bottles up to 3.8 in (9.7 cm) in diameter. Two twist-lock sleeves and a set of snap-in plugs step the cup down in small increments, so bottles of various sizes sit snug instead of bouncing around. One sleeve comes in the accent color of your choice, so you can match your Fiesta’s color theme and your style.

WHY YOU’LL WANT IT
The factory cup holder is only 3.07 in (7.8 cm) wide. Most big tumblers and wide-mouth bottles are wider than that, so they tip over or won’t go in at all. This adapter gives them a stable seat on the console around the holder. Unlike a generic universal cup holder, it is optimized for the Fiesta’s unique cup holder shape, so it fits better, locks into place, and installs without any hassle. You also choose the accent color of one sleeve to match your interior design preference. The diamond-pattern walls let your bottle’s color show through. It also clears the parking brake, so the handle moves freely with the adapter installed.

WHAT’S IN THE SET
– 1 black cup holder adapter
– 2 sleeves: one in your choice of accent color, one in black
– 24 black snap-in resizing plugs: 8 each in 3 sizes
– 1 removal tool

HOW IT WORKS
The adapter snaps into place with its spring tabs and holds bottles up to 3.8 in (9.7 cm). For smaller bottles, two sleeves and snap-in plugs narrow the opening in steps: the accent-color sleeve alone, or the accent-color and black sleeves together for the smallest opening. The sleeves come pre-installed. Each sleeve locks in with hinged slugs that click into the small diamond holes, and you can remove a sleeve whenever you need to with the included removal tool. The plugs then fine-tune the diameter in small increments on top of any sleeve setting. They snap into the small upper and lower diamond holes, and you can use more than one plug, or more than one plug size, at a time. Together, the sleeves and plug sizes give 12 diameter settings. To remove the adapter, push in the spring tabs with the removal tool or by hand, then lift it out.

A SIZE FOR NEARLY EVERY BOTTLE
Mix and match the sleeves and plugs to fit your bottle. Largest bottle diameter:
– No sleeve: 3.8 in (9.7 cm) and smaller
– With the accent-color sleeve only: 3.6 in (9.2 cm) and smaller
– With the accent-color and black sleeves together: 3.4 in (8.6 cm) and smaller

All 12 diameter settings: 3.81, 3.78, 3.69, 3.63, 3.62, 3.60, 3.50, 3.44, 3.39, 3.36, 3.26, 3.20 in (96.8, 96.0, 93.6, 92.2, 92.0, 91.4, 89.0, 87.4, 86.1, 85.3, 82.9, 81.3 mm)

BOTTLES THAT FIT
Tested in this adapter:
– No sleeve: Owala FreeSip 40 oz, YETI Rambler 36 oz, Nalgene 32 oz wide mouth
– With the accent-color sleeve only: Owala FreeSip 32 oz, YETI Rambler 26 oz, Hydro Flask 32 oz wide mouth, Gatorade 32 oz

Not tested yet, but expected to fit based on the manufacturers’ published sizes:
– With the accent-color sleeve only: Hydro Flask 40 oz wide mouth
– With the accent-color and black sleeves together: YETI Rambler 30 oz
– With the accent-color and black sleeves together, plus plugs: Owala FreeSip 24 oz

Bottles under 3.0 in (7.6 cm) across already fit the factory holder, so you don’t need the adapter for those.

PLEASE CHECK YOUR BOTTLE BEFORE YOU BUY
It is your responsibility to measure your bottle’s diameter and make sure it fits before you purchase. The dimensions listed here come from manufacturers’ published sizes and other sources, and may not match your actual bottle.

WON’T FIT
Bottles wider than 3.8 in (9.7 cm), such as the YETI Rambler 46 oz and 64 oz jugs.

FITMENT
– Ford Fiesta, [2014-2019], rear cup holder (the one behind the lower holder)

QUALITY: Products are 3D-printed, so visible textures and minor imperfections are a natural part of the process. These do not significantly affect the appearance or functionality. I guarantee the durability of all my products.

WARRANTY: I guarantee the durability and fit of my products. Free replacements are available for failures under normal use—just cover shipping. Minor imperfections are normal with 3D printing. Feel free to reach out with any questions.

MATERIALS AND MAKING: Printed in Maryland in ASA and PETG.